MHS-TS10 / TS20 / TS20K Firmware update for Windows and Mac OS X

Important notes:

• Before performing the firmware update, make sure your bloggie™ touch Mobile HD snap camera is fully charged.

Step 1: download the firmware update

1. Make sure that you are logged on as a user with administrative rights.
2. After reading the disclaimer, click the [Accept] button at the bottom of the page.
3. The download of the [FIRMWARE.BIN] file (9,89 MB (10.375.168 bytes)) will start.
4. Save the file to the desktop of your computer (recommended).

Step 2: Connect the bloggie™ touch Mobile HD snap camera to the computer with the supplied USB connection support cable

For Windows:

1. Connect the camera to the computer with the supplied USB connection support cable.
   "USB Mode / Mass Storage" appears on the LCD screen.
   
   
   
   
2. The computer will detect two drives as follows:
   
   Note: drive letters might be different depending on your computer environment.
   • "BLOGGIE(D:)"
   • "Bloggie Software(E:)" or "BLOGGIE_SW(E:)"
   
   Note: if "LUN Settings" (found in your bloggie™ touch under (Settings) --> [LUN Settings]) is set to "Single", the computer will only detect one drive as follows:
   • "BLOGGIE(D:)"

For Mac OS:

1. Connect the camera to the computer with the supplied USB connection support cable.
   "USB Mode / Mass Storage" appears on the LCD screen.
   
   
   
   
2. The computer will detect two drives as follows:
   • "BLOGGIE"
   • "BLOGGIE_SW"
   
   Note: if "LUN Settings" (found in your bloggie™ touch under (Settings) --> [LUN Settings]) is set to "Single", the computer will only detect one drive as follows:
   • "BLOGGIE"

Step 3: Copy the firmware to the internal memory of the bloggie™ touch Mobile HD snap camera

For Windows:

1. • If your computer detected 2 drives at Step 2:
     1. Double-click the drive which has the smallest drive letter.
        ("BLOGGIE(D:)" in the example provided at Step 2)
        Note: drive letters might be different depending on your computer environment.
     2. Copy the downloaded "FIRMWARE.BIN" file from the desktop of your computer to that drive.
   • If your computer detected only 1 drive at Step 2:
     1. Double-click the drive that has been detected.
        ("Bloggie(D:)" in the example provided at Step 2)
     2. Copy the downloaded "FIRMWARE.BIN" file from the desktop of your computer to that drive.
2. Disconnect the camera from the computer by following the below procedure:
   1. Double-click on the task tray.
      
      
      
      
   2. Click (USB Mass Storage Device) --> [Stop].
   3. Confirm the device on the confirmation window, then click [OK].
   4. Click [OK].
   5. The device is disconnected.
      
      Note: Step 4 is unnecessary for Windows XP.
3. Disconnect the USB connection support cable from the camera.

For Mac OS:

1. • If your computer detected 2 drives at Step 2:
     1. Double-click the drive labelled as "BLOGGIE".
     2. Copy the downloaded "FIRMWARE.BIN" file from the desktop of your computer to that drive.
   • If your computer detected only 1 drive at Step 2:
     1. Double-click the drive that has been detected.
     2. Copy the downloaded "FIRMWARE.BIN" file from the desktop of your computer to that drive.
2. Disconnect the camera from the computer by following the below procedure:
   • Drag and drop the icon of the drive to the "Trash" icon before disconnecting.
     
3. Disconnect the USB connection support cable from the camera.

Step 4: Start the firmware update

1. Confirm that the battery icon at the upper-right corner of the LCD sccreen is full.
2. Turn off the camera by pressing the "ON/OFF" button.
3. Press the "ON/OFF" button again to turn on the camera.
4. The firmware update will start automatically.
5. An animated message appears on the LCD screen as illustrated below.
   
   
   
   
6. After 10 seconds, the camera will reboot automatically.
   
   Note: Do not turn off the camera while updating the firmware, or the camera may be dammaged.

Step 5: Check that your bloggie™ touch Mobile HD snap camera works correctly and confirm the firmware version is 1.05

1. Turn on your camera and confirm the system starts correctly.
2. Check the firmware version is 1.05 by following the procedure detailled at the top of the page under the "About this update" section.

Note:

If your camera does not start up anymore after performing the firmware update, please contact Sony